The length conversion system is given below

 

Length Conversion

From

To

Conversion Factor

Inches (in)

Feet (ft)

1 in = 0.08333 ft

Feet (ft)

Inches (in)

1 ft = 12 in

Meters (m)

Feet (ft)

1 m = 3.28084 ft

Meters (m)

Inches (in)

1 m = 39.3701 in

Feet (ft)

Meters (m)

1 ft = 0.3048 m

Millimeters (mm)

Meters (m)

1 mm = 0.001 m

Meters (m)

Millimeters (mm)

1 m = 1,000 mm

Millimeters (mm)

Inches (in)

1 mm = 0.0393701 in

Note :Please share if you like it.

Comments

Post a Comment

Popular posts from this blog

Live Load Calculation Bangladesh National Building Code (BNBC) 2020

 Live load is calculated According to the Type of building Bangladesh National Building Code (BNBC) 2020 Bangladesh National Building Code (BNBC) 2020 , live loads refer to the loads that are not permanently attached to the structure. These loads are important for the design and structural integrity of buildings. The live load values are specified depending on the type of building use and occupancy. Here’s a table with typical live load values in PSF (pounds per square foot) and kN/m² (kilonewtons per square meter) based on common building usages, as per the BNBC 2020 or similar standards: Live Load - BNBC 2020 Sl Occupancy or Use Live Load (Psf) Live Load (KN/m²) 01 Roofs (ordinary) 20 0.96 02 One and two-family dwellings 40 1.92 03 Apartment buildings, dormitories, hotels 40 1.92 04 ...
Read more

Description of Seismic Zones of Bangladesh as per BNBC 2020:

Image
 Description of Seismic Zones of Bangladesh as per BNBC 2020: . According to BNBC 2020, the different regions of Bangladesh have been divided into four parts according to the intensity of earthquakes. These are 1/ Less earthquake prone area 2/ Medium earthquake prone area 3/ Severe earthquake prone areas 4/ Very serious earthquake prone area 1/ Less earthquake prone areas: It includes the south western region of Bangladesh Barisal Khulna Jessore, Rajshahi... Seismic Zone Coefficient, Z= 0.12 2/ Medium earthquake prone area It includes lower central and north western parts Noakhali Dhaka Pabna Dinajpur Also parts of southern region including Sundarbans the Seismic Zone Coefficient of these regions, Z= 0.2 3/ Severe earthquake prone areas Upper Central and North-Western parts which include ........... Brahmonbaria Sirajganj Rangpur Seismic Zone Coefficient of these regions, Z = 0.28 4/ Very serious earthquake prone area North Eastern part which includes Sylhet, Mymeningh, Kurigram Se...
Read more

Using the 3-4-5 Method of Building Layout

Image
Why does the building layout follow the 3-4-5 Method? Identify a Base Line: 1. Start by marking a baseline along one edge of the area where the right angle is needed. For example, this could be the edge of a foundation or a wall. Measure Along the Base: 2. From one end of the baseline, measure 3 units along this line. Mark the end of this measurement as Point A. Measure Perpendicular Line: 3. From the same starting point (Point O), measure 4 units at approximately a 90-degree angle to the base. You can use an adjustable square or approximate the angle by eye. Mark the end of this measurement as Point B. Check the Hypotenuse: 4. Measure the distance between Point A (on the baseline) and Point B (on the perpendicular line). If the distance is exactly 5 units, then the angle between the two lines is a perfect 90-degree angle. By following these steps, you can quickly and accurately establish a square layout for building foundations or other construction projects.
Read more